SILIC-ONE

Addition silicone impression material.

- Precision
- Dimensional stability
- Practicality
- Excellent hydrophilicity
- Excellent working time
- High rupture strength
- Vivid colors: greater visibility

Benefits

Precision

Dimensional stability

Practicality

Excellent hydrophilicity

Excellent working time

High rupture strength

Vivid colors:
greater visibility

Recommendations

SILIC-ONE line of products is indicated for dental impression techniques, specifically for:

Silic-one Putty Soft: Primary impression of implants, prosthetic components, indirect restorations, dental prostheses, edentulous arches, removable partial prostheses, veneers and crowns on teeth;

Silic-one Heavy Body and Light Body: Indicated for reproducing finer details when molding implants, prosthetic components, indirect restorations, dental prostheses, edentulous arches, removable partial prostheses, veneers and crowns on teeth. They can also be used to perform rebasing of complete prostheses;

Silic-one Clear Body: Indicated for fabricating colorless silicone guides for the veneer technique with injectable composites;

Silic-one Bite Registration: Indicated for fabricating occlusal registration with precision.

Technical parameter	Putty Soft	Bite Registration	Heavy Body	Clear Body	Light Body
Type	0	0	1	2	3
Mixing time	30”	–	–	–	–
Total working time	1’30”	20”	1’30”	1’30”	2’15”
Curing time in the oral cavity	3’00”	45”	3’00”	3’00”	3’30”

* Tip: The working time mentioned considers room temperature (23°C) and normal air humidity (50%). The time may be shorter at higher temperatures and longer at lower temperatures.

Commercial Availability

Minikit: 1 container of Putty Soft base paste with 400g + 1 container of Putty Soft catalyst paste with 400g + 1 Light Body cartridge with 50ml + 6 mixing tips + 6 intraoral tips + 2 measuring spoons.

Kit: 1 container of Putty Soft base paste with 400g + 1 container of Putty Soft catalyst paste with 400g + 2 Light Body cartridges com 50ml + 12 mixing tips + 12 intraoral tips + 2 measuring spoons.

Putty Soft Refill: 1 container of base paste with 400g + 1 container of catalyst paste with 400g + 2 measuring spoons.

Light Body 1 Refill: 1 cartridge with 50ml + 6 mixing tips + 6 intraoral tips.

Light Body 2 Refill: 2 cartridges with 50ml each + 12 mixing tips + 12 intraoral tips.

Heavy Body Refill: 1 cartridge with 50ml + 3 mixing tips.

Bite Registration 1 Refill: 1 cartridge with 50ml + 3 mixing tips.

Clear Body Refill: 1 cartridge with 50ml + 3 mixing tips.

Step by step

Tray selection

The impression material can be applied to all types of trays. To increase retention between them, a thin layer of adhesive can be applied to the inside of the tray.

Manual mixing: Silic-one Putty Soft Paste

1. Use the respective color spoons to measure out the same weight or volume of the base paste and catalyst paste (close the packages immediately after use and do not exchange the lids). 2. Mix them together with your fingertips and knead them for at least 30 seconds, until they are evenly mixed. 3. Place the material in previously selected trays and make the impression. Note: If gloves are used during the procedure, it is recommended that a compatibility test of the impression material with the glove be performed. Certain types of gloves, such as latex gloves, may impede the polymerization process.

Material in cartridges: Silic-one Heavy Body, Light Body, Bite Registration and Clear Body

1. Adapt the cartridge to the dispensing gun in a 1:1 ratio. 2. Remove the cartridge cap, attach the mixing tip and, if necessary, the intraoral tip. 3. Activate the gun trigger, dispensing a small amount until a homogeneous mixture of the product is obtained. 4. Apply the silicone in the desired location and wait the necessary time (see indicative table) for the polymerization process of the material. Note: After use, it is suggested not to remove the mixing tip, keeping it as a cover, and it should only be changed in the next impression.

Tray selection

The impression material can be applied to all types of trays. To increase retention between them, a thin layer of adhesive can be applied to the inside of the tray.