IFU

Whiteness Simple

Carbamide peroxide whitening system for vital teeth at 10%, 16%, and 22% for supervised take-home whitening.

  • Contains desensitizing actives: sodium fluoride and potassium ions
  • Ideal viscosity

Benefits

Desensitizing action:
Sodium fluoride and potassium ions.

Excellent viscosity: 
Does not run off the tray.

High Yield:
Each syringe of 3g yields up to 9 applications.

Recommended daily use time:
• 10% and 16%- 3 to 4h or overnight. • 22% - 1 h.

Nominations

Whitening of vital teeth using the take-home whitening technique supervised by a dentist.

Presentation

Kit 10%, 16% and 22%

• 5 syringes with 3g of gel each
• 5 applicator tips
• 2 plates for preparing the trays;
• 1 tray case

 

Packaging with 3 syringes

• 3 syringes with 3g of gel each
• 3 applicator tips.

Step by step

foto-1-11[1]
Step 1 of 7
Register the teeth shade so that the dentist and the patient can have a comparison parameter for the whitening. Recording of teeth shade can be made using a shade guide or a photograph.
moldagem[1]
Step 2 of 7
Molding: molding can be made with alginate and must properly copy all teeth that will be whitened.
foto-3-1-1_1[1]
Step 3 of 7
Mold is made of stone-gypsum, in order to prevent bubbles. It is not necessary to relief the model to create gel shells.
foto-4-1-1[1]
Step 4 of 7
Place the 1mm acetate plate Whiteness Plates for Molds (FGM) into the thermal laminator until forming a slight bending due to the heat. Then, pull the plastic-state plate over the gypsum model, so the suction can thermal format the mold into the model. The plate’s removal must be made after it has fully cooled down.
foto-5-1[1]
Step 5 of 7
After removing the mold from the model, cut it without burrs and to cover 1 to 2mm of the gums margin.
foto-6-1[1]
Step 6 of 7
Mold test: the mold must not compress the soft tissue, nor present excessive gaps.
foto-3-1-4[1]
Step 7 of 7
Show to the patient the quantity of gel that should be applied to the tray. One drop of gel must be put into the areas corresponding to the vestibular faces of the teeth that will be whitened. Usage time: 3 to 4 hours per day for concentrations between 10 and 16%, and 1 hour per day for 22% concentration.
foto-1-11[1]
Step 1 of 7
Register the teeth shade so that the dentist and the patient can have a comparison parameter for the whitening. Recording of teeth shade can be made using a shade guide or a photograph.
moldagem[1]
Step 2 of 7
Molding: molding can be made with alginate and must properly copy all teeth that will be whitened.
foto-3-1-1_1[1]
Step 3 of 7
Mold is made of stone-gypsum, in order to prevent bubbles. It is not necessary to relief the model to create gel shells.
foto-4-1-1[1]
Step 4 of 7
Place the 1mm acetate plate Whiteness Plates for Molds (FGM) into the thermal laminator until forming a slight bending due to the heat. Then, pull the plastic-state plate over the gypsum model, so the suction can thermal format the mold into the model. The plate’s removal must be made after it has fully cooled down.
foto-5-1[1]
Step 5 of 7
After removing the mold from the model, cut it without burrs and to cover 1 to 2mm of the gums margin.
foto-6-1[1]
Step 6 of 7
Mold test: the mold must not compress the soft tissue, nor present excessive gaps.
foto-3-1-4[1]
Step 7 of 7
Show to the patient the quantity of gel that should be applied to the tray. One drop of gel must be put into the areas corresponding to the vestibular faces of the teeth that will be whitened. Usage time: 3 to 4 hours per day for concentrations between 10 and 16%, and 1 hour per day for 22% concentration.
plugins premium WordPress

Selecione seu idioma

Select your language