<iframe src="https://tagging.fgmdentalgroup.com/ns.html?id=GTM-KDV4HRF" height="0" width="0" style="display:none;visibility:hidden"></iframe>

Home » Produtos Estética » Ambar APS

Ambar APS

Light-curing adhesive system for enamel and dentin.

2-step conventional adhesive: primer and bond in the same bottle
Light-curing
APS Technology: excellent performance at any moisture level of dentin

Benefits

Increased polymerization standard and decreased sensitivity to moisture:
Benefits of the APS technology. Ideal for areas with difficult control of the moisture level, such as in restorations on lower teeth or very close to the gums.

Higher adhesive potential:
The presence of MDP in the composition makes a chemical bond with the dental structure, which adds mechanical adhesion, which gives to the product a superior and long-term adhesive strength.

High conversion degree:
Provides greater stability of the adhesive interface.

Higher stability and resistance for the adhesive film:
Due to the presence of treated silica nanoparticles.

BPA-free:
Ensures safety and health.

Colorless aspect:
Does not interfere on the esthetics of restorations and cementations.

Recommendations

All classes of direct restorations with composites (classes I, II, III, IV and V) and light-curing glass-ionomer cements.

Adhesive cementation (together with resin cement) of prosthetic pieces (posts/cores, crowns, onlays/inlays and veneers) made of fiberglass, ceromer, ceramic, composite and metal.

Adhesive repairs in ceramics and composites.

Commercial Availability

Single 6ml bottle

• 6ml of primer + adhesive.

frasco_aberto_ambar_aps

frasco_ambar_aps

caixa_ambar_aps

Step by step

Foto-1_1[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/Foto-1_12.jpg" class="jet-carousel__item-img" alt="Foto-1_1[2]" loading="lazy">

Step 1 of 5

The surface to be restored must be cleaned and then etched with phosphoric acid at 37% Condac 37 (FGM) for 15 seconds (same time for enamel and dentin). It is important to isolate the tooth, whether with complete or relative isolation (depending on the case).

foto-2[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-22.jpg" class="jet-carousel__item-img" alt="foto-2[2]" loading="lazy">

Step 2 of 5

Rinse the surface with abundant water and dry the cavity until it is moist, not dehydrated.

foto-3-1[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-3-12.jpg" class="jet-carousel__item-img" alt="foto-3-1[2]" loading="lazy">

Step 3 of 5

With a micro-applicator Cavibrush (FGM), apply the adhesive rubbing the first drop of the product for 10 seconds. Next, apply a new layer of adhesive to the same surface for other 10 seconds.

foto-4-1[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-4-12.jpg" class="jet-carousel__item-img" alt="foto-4-1[2]" loading="lazy">

Step 4 of 5

Apply an air jet for 10 seconds, which helps to evaporate the solvent and, consequently to increase adhesion.

foto-5[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-52.jpg" class="jet-carousel__item-img" alt="foto-5[2]" loading="lazy">

Step 5 of 5

The adhesive must be light-cured for 10 seconds, then perform restoration. Note: for intracanal adhesive application, the photoactivation time must be extended to 20 seconds.

Foto-1_1[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/Foto-1_12.jpg" class="jet-carousel__item-img" alt="Foto-1_1[2]" loading="lazy">

Step 1 of 5

The surface to be restored must be cleaned and then etched with phosphoric acid at 37% Condac 37 (FGM) for 15 seconds (same time for enamel and dentin). It is important to isolate the tooth, whether with complete or relative isolation (depending on the case).

foto-2[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-22.jpg" class="jet-carousel__item-img" alt="foto-2[2]" loading="lazy">

Step 2 of 5

Rinse the surface with abundant water and dry the cavity until it is moist, not dehydrated.

foto-3-1[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-3-12.jpg" class="jet-carousel__item-img" alt="foto-3-1[2]" loading="lazy">

Step 3 of 5

With a micro-applicator Cavibrush (FGM), apply the adhesive rubbing the first drop of the product for 10 seconds. Next, apply a new layer of adhesive to the same surface for other 10 seconds.

foto-4-1[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-4-12.jpg" class="jet-carousel__item-img" alt="foto-4-1[2]" loading="lazy">

Step 4 of 5

Apply an air jet for 10 seconds, which helps to evaporate the solvent and, consequently to increase adhesion.

foto-5[2]

<img width="354" height="236" src="https://fgmdentalgroup.com/wp-content/uploads/2022/11/foto-52.jpg" class="jet-carousel__item-img" alt="foto-5[2]" loading="lazy">

Step 5 of 5

The adhesive must be light-cured for 10 seconds, then perform restoration. Note: for intracanal adhesive application, the photoactivation time must be extended to 20 seconds.

Scientific evidence

We provide direct links to publications from major scientific portals containing studies conducted with our products.

Links

Other products

Light-curing adhesive system for enamel and dentin.

75iawtehdq_bpafree_ambar__02-300x268[1]

Self-curing glass ionomer for restoration.

5oprtqkkdn_maxxR-286x300[1]

Ambar Universal APS

Self-etching light-curing adhesive system for enamel and dentin.

22yoymx3h9_Sem_t_tulo_2_Prancheta_1_c_pia1-300x269[1]