Ambar Universal APS

Ambar Universal APS

Self-etching light-curing adhesive system for enamel and dentin.

Selos

  • Universal Adhesive (use under different acid etching protocols and on different surfaces);
  • Minimizes post-operative sensitivity;
  • APS system: Excellent performance at any moisture level of dentin;
  • Perfect for intracanal application.

Sem Título 2 Prancheta 1 Cópia1

Benefits

High adhesion in different forms of application: Self-etching, selective-etching on enamel or total-etching.

Adhesion to different types of surface: Metals, ceramics, CAD/CAM composite and intracanal posts.

Perfect for intracanal application:
• High adhesion rates in the intracanal region;
• Better polymerization even in the apical region;
• Greater compatibility with dual cements.

Enhanced MDP: In Ambar Universal APS, the MDP is more reactive, which has been achieved by redistributing the concentrations between solvents, water and acidic monomers. This higher reactivity increases the adhesive capacity to dentin (mainly without previous acid etching) and indirect substrates, besides providing adhesive film stability.

BPA-free: Ensures safety and health.

Colorless aspect:Does not interfere on the esthetics of restorations and cementations.

Recommendations

All classes of direct restorations with composites (classes I, II, III, IV and V).

Adhesive cementation (together with resin cement) of prosthetic pieces (intraradicular posts/cores, crowns, onlays/inlays, veneers etc.), fiberglass, ceromer, ceramic, composite and metal.

Adhesive repairs in ceramics and composites.

As a primer for metal or ceramic (etching or non-etching).

Commercial Availability

Packaging containing

• 1 bottle with 5ml of adhesive.

Packaging containing

• 1 bottle with 5ml of adhesive.

Step by step

Total-etching method:

The surface to be restored must be cleaned and then etched with phosphoric acid at 37% Condac 37 (FGM) for 15 seconds (same time for enamel and dentin). It is important to isolate the tooth, whether with complete or relative isolation (depending on the case).1

Rinse the surface with abundant water and dry the cavity until it is moist, not dehydrated.2

With a micro-applicator Cavibrush (FGM), apply the adhesive rubbing the first drop of the product for 10 seconds. Next, apply a new layer of adhesive to the same surface for other 10 seconds.3

Apply an air jet for 10 seconds, which helps to evaporate the solvent and, consequently, to increase adhesion.4

The adhesive must be light-cured for 10 seconds, then perform restoration. Note: for intracanal adhesive application, the photoactivation time must be extended to 20 seconds.5

Selective-etching method:

The surface to be restored must be cleaned and then etched with phosphoric acid at 37% Condac 37 (FGM) for 15 seconds (same time for enamel and dentin). It is important to isolate the tooth, whether with complete or relative isolation (depending on the case).6

Rinse the surface with abundant water and dry the cavity until it is moist, not dehydrated.7

Apply the adhesive to the tooth surface using a Cavibrush (FGM) micro-applicator. The first layer must be vigorously applied rubbing the micro-applicator in the surface for 10 seconds. Next, apply a new adhesive layer over the same surface for other 10 seconds. Then, apply air jet for 10 seconds, helping to evaporate the solvent and increase adhesion.8

The adhesive must be light-cured for 10 seconds, then perform restoration. Note: for intracanal adhesive application, the photoactivation time must be extended to 20 seconds.9

Self-etching method:
There is no need to acid etch the enamel or dentin.

Apply the adhesive to the tooth surface using a Cavibrush (FGM) micro-applicator. The first layer must be vigorously applied rubbing the micro-applicator in the surface for 10 seconds. Next, apply a new adhesive layer over the same surface for other 10 seconds. Then, apply air jet for 10 seconds, helping to evaporate the solvent and increase adhesion.Image11 3 300x200

The adhesive must be light-cured for 10 seconds, then perform restoration. Note: for intracanal adhesive application, the photoactivation time must be extended to 20 seconds.12

As primer for etchable ceramics:

Etch the internal surface of the piece with fluoride acid (Condac Porcelana – FGM) and apply the silane agent (Prosil – FGM) prior to applying the adhesive to the piece. Using a disposable micro-applicator (Cavibrush – FGM), apply the adhesive to the inside surface of the piece by rubbing it, wait for 15 seconds and then apply a light air jet for 10 seconds.Foto 13 300x200